Top 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.
Top 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.
Blog Article
Do not take too lightly the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several accidents involving forklifts.
Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the personnel illegally, the forklift vehicle driver does not use the seat belt, the forklift lifter falls and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.
Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially confirm that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.
Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are banned. High-speed doglegs will create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever run with diseases or hide them.
packing and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought to also be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, Electric Forklift Truck for Warehouse the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free Electric Forklift Truck for Warehouse turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and move on, if they encounter huge or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844